Відео

Hand warmer

I have the exact same machine and my gear selector lever doesn’t stay in any of the middle gear……loose except rear and full forwards. Any ideas or suggestions?

I jave a seadoo gtx supper charged i always have trouble starting it i put just regular gas in it to i need to put the higher octane gas in it is the the reason why i have trouble starting it

Was the brake pedal going way down close to the floor when the light was on ?

with a Suzuki motor!!! so cool!

Great information, Thank you. I would like you to see how to clean and degrease the unit.

Who is herr in 2024🎉

Wish you showed the wiring connections and battery placement.

Are you sure you did not explain it the weong way around? The wind flap, when pushed away from the ventilator, should close (!) the choke, so to skow down the RPM; that's to keep the RPM constant, in effect. - Or am I wrong?

Informative video but I really think you should stay in Canada

Good video. My mower will not start when hot because the thermostat has the choke open. Anything I can do but have a coffee while it cools down and finish mowing the lawn?

Thanks for sharing this

Great vid ,thanks, helped allot

Omg thank you I'm expecting the same thing and just put a new starter in

Great instructional video! Thanks so much!

Do u still have it for sale

Really helpful advice thank you

Looking for a +9kW diesel generator...don't think they float around the scrapyard, but you'd know better than me.

Very nice family addition...1999 R1100s is in my garage...28,000 miles...canyon red...be safe!

My onan gas generator muffler exit pipe was badly rusted and disintegrated in few pieces and disappeared behind us on the road. After that. a few days later. My ABS light turned on and off randomly. I did not had braking issue. but i think there is a lose wire and connection lose somewhere. Do you know who to troubleshoot that?

please look up the Chinese "no compete agreement" that ended in 2000 or 2001..... youll learn how thats not actually a "copy" of a Honda at all.... the GN designation on engine should be a huge clue

Thank you buddy!!

So I have this mower. Runs fine. But push button starter doesn’t work, nor will it cut off when I release the handle. Also plastic key won’t switch left to off position. Thoughts. I took apart down to view of auto start mechanism. Afraid to pull apart as don’t know what’s inside and screwing it up. My assumption is it frozen up somehow. Thanks.

$40 THAT IS A LOT

Thank you brother it worked💯

Let my just but out my ultrasonic carb cleaner that everyone has lol😂

Exactly what I was looking for!

Although your beam seams heavy enough to withstand the mowers weight it is not bearing all the weight. Instead all the weight is placed solely on the eye screw which I wouldn't consider safe as it could fail and rip out! A safer way would be to rap a good size heavy chain around the beam and then run your hoist off the chain. Safer and stronger support transfered totally to the beam instead of an eye bolt!

replaced the carburetor exactly as you did......and still having problems......after running about 5 seconds the engines shuts off.....even when I tilt to the right it shuts off....but not to the left.....any suggestions?

Thanks needed this

Greeting I have one question. I have the same machine (OHV). My pulling rope broke - start. Do you have such a video on how to change the rope? Thank you in advance.

I worked on my 86 ht-3009 and now it will not run.I will take an other run at it when my brain pain lightens up.

Is it oil and gaz resistant?

Am ibthe only one that doesn't have a 91075 puller in my pocket at all time?

Fantastic vid

How did these treat ya?

I bought 4 primer bubbles from my local dealer cost me $32 Canadian...ordered a carb be here tommorow from amazon

Ugliest Mustangs ever

I wish I could pay you to fix mine

Mercury outboards used to have a direct reverse also . They called they “dock busters “. lol. This is a G1 . Serial number is on the right or left frame behind the wheel well. 🙋‍♂️👍🖖🏻

TYSM BRO

U had an aftermarket Wiring or You modifieed yours?

I have the MM875. It will be 19 years old in July 2024. It is in for repair now for the brush (fingers crossed). I had bought an MM2000 a few weeks ago and returned it because I couldn’t lower the handle to waist height. I spoke to a B&D CSR who said the handle could not be lowered; you have to match the arrow on one part with either the 1 or the 2 on the other part which leaves the handle at my collar bone. I was hoping you addressed this issue here.

Hi, I'm in the process of doing the same conversion. Wanted to ask you what you did for a fuel pump. Did you go external or in the tank. Any info is appreciated

Thanks!

Done it yet but I need to i don't think you can just do it like that i have to go to FS office. Don't I

Lmao yeah maybe if you're that lazy to take care of your crap and clean it once a month. A steel deck should be cleaned regularly

Excellent! I'll be doing this tomorrow! Thank you!

I have only watched one and a half videos on this channel and am now a subscriber. When you get valuable information in the first 90 seconds of a video, the channel is worth its salt. Thanks a ton!!

I have my firman for 5 years, works great